Direct answer Yes, with conditions: feed treated water below 50 ppm TDS, give the mist at least 2.5 m to evaporate before it reaches product, and keep the machine serviceable from outside the clean zone. Skip those and ultrasonic atomisation puts mineral aerosol and microorganisms into the room, which is why many ISO classified areas specify steam instead. 40–60% RHBand ISO 14644-2 monitoring ...

Direct answer Clean the tank weekly, descale the transducers monthly with a citric acid solution, replace or regenerate the demineralisation cartridge every 200 to 600 operating hours, and plan on new transducers every 8,000 to 12,000 hours. Skipping the schedule is expensive: mineral scale cuts mist output by 30 to 50 percent long before anything visibly breaks. 2–4 wkStructured service inter...

Direct answer Ultrasonic humidifiers need demineralised water. Most manufacturers specify reverse osmosis or deionised feed with total dissolved solids below 50 parts per million and conductivity in the range of 2 to 15 microsiemens per centimetre. Tap water above roughly 200 ppm leaves visible white dust, scales the transducers and shortens service life. Feed water TDS target 2–15 µS/cmConduc...

Direct answer Yes. A combined constant humidity unit holds a single setpoint in both directions, switching between modes across a dead band of about 5 percent RH. Industrial ranges run roughly 90 to 480 litres per day of dehumidification against 3 to 40 kilograms per hour of humidification, with control accuracy around plus or minus 3 percent RH. 90–480 L/dayDehumidification capacity range 3–4...

Direct answer Battery workshops are graded by process, not by one number. Slurry mixing runs below 5 percent RH, coating below 1 percent, cell assembly around 0.1 percent and electrolyte filling at 0.02 percent. That is minus 20 to minus 65 degrees Celsius dew point, held at 20 to 25 degrees Celsius with 20 to 50 air changes per hour. −40 °C dpStandard dew point target for cell work 20–25 °CRo...

Direct answer Ultrasonic, by a wide margin: roughly 0.05–0.10 kWh per kilogram of water against 0.70–0.85 kWh for electric steam and 0.65–0.75 kWh for gas-fired — 85–93% less. A 10 kg/h ultrasonic unit draws about 300–400 W where steam draws 7–8 kW, and payback on a changeover is typically 12–36 months. Steam still wins where sterile output, mineral tolerance or a large heat input is required. ...

Direct answer A piezoelectric transducer submerged in water vibrates at about 1.7 MHz. Cavitation bubbles implode against the surface and capillary waves tear droplets off the water film, producing a cloud of 1–5 µm droplets that evaporate before they settle. Nothing is heated, so the process is adiabatic and costs roughly 0.05–0.10 kWh per kilogram against 0.70–0.85 kWh for electric steam — 85...

Direct answer Work in mass, not floor area. Base load in kg/h is volume (m³) × air changes per hour × the absolute humidity gap Δg (g/m³) ÷ 1,000. Then add infiltration — 15% for tight construction, 25% average, 40% for high traffic — allow for hygroscopic material absorbing 10–30% of what you supply, and apply a 1.2–1.3 safety factor. Sizing on area alone is the most common and most expensive ...

Direct answer Because dry air is a defect source. Below about 40% RH, electrostatic charge stops dissipating and discharge events damage components; most electronics specifications set 40–60% RH with ±5% tolerance. Battery plants need both directions: electrode and cell rooms run as dry rooms at dew points down to −40 °C, while module and pack assembly, test and packing areas need 40–55% RH hum...

Direct answer An industrial humidifier holds a building at the relative humidity a process needs — most often 40–60% RH, with a tolerance of about ±5%. It is used to suppress static in electronics, stop fibre and paper losing moisture in textile and print, hold weight in cold storage, and keep timber dimensionally stable. Capacity is specified in kg/h of water and is driven by air change rate, ...